Introduction: The Most Common Question in Outdoor Design Across the U.S., outdoor living is shifting from “nice-to-have” patios to fully designed year-round outdoor rooms—complete with pergolas, swings, heaters, outdoor kitchens, and fire features. And naturally, everyone asks: “Can I put a fire pit under my covered patio?” The short answer:Yes—but only if you set it […]
Can You Put a Fire Pit Under a Covered Patio? Read More »
Concrete/GFRC fire features WILL develop charring and non-structural cracking, aka hairline cracks. This is the nature of concrete and thus, not covered by warranty.
For the ultimate durability, consider a steel, aluminum, or ready to finish fire pit.
Nearly ALL concrete fire pits, whether sold by Montana Fire Pits or others, will eventually develop the same characteristics of browning/charring AND hairline cracks. The cracks can appear anywhere on the concrete shell, but are most prominent on the inside ledges nearest the fire. Visibility of the hairline cracks has been known to diminish when the unit is dry. The cracks will re-appear when any moisture is present. These characteristics can develop as soon as 20 minutes after lighting the fire.
Exceptions:
Shipping damage that has been properly photographed and documented by the receiver, as well as submitted to Montana Fire Pits within 3 days of delivery, OR ideally the shipment is refused, will be considered for a freight claim based on evidence provided by you, the customer or receiver.
If you wish to proceed with a concrete fire system, we’ll send you a document to sign which is your acknowledgement that the warranty does not cover cracking, charring, or chipping.
Steel
Aluminum
Our hardwood covers turn your fire system into a beautiful, functional table.
Durability
Considerations
Steel
Aluminum
Hardwood
You have reached our top status… Pro Solutions Platinum. Enjoy our best pricing.
If you have documents to prove exemption from your state sales tax, visit YOUR ACCOUNT and click on “Tax Exemption”.
Applies to most orders over $99 in the continental U.S. See Shipping Details
Mon – Fri: 9am – 4:30pm MST
Sat – Sun: Closed
You will reach PLATINUM status after orders totaling $20,000 or more.
If you have documents to prove exemption from your state sales tax, visit YOUR ACCOUNT and click on “Tax Exemption”.
Applies to most orders over $99 in the continental U.S. See Shipping Details
Mon – Fri: 9am – 4:30pm MST
Sat – Sun: Closed
Expert advice comes standard
Tel: (833) 228-5244
Mon – Fri: 9am – 4:30pm MST
Sat – Sun: Closed
Planning to stop by? Please SCHEDULE AN APPOINTMENT before coming. Thanks!
Manufacturing
2302 McDonald Ave
Missoula, MT 59801
Sales & Support
1821 South Ave W.
Suite 303
Missoula, MT 59801
Your local gas professional (plumber, HVAC, propane supplier, etc…) needs to know these requirements
Your local gas professional (plumber, HVAC, propane supplier, etc…) needs to know these requirements
There are various pros/cons of Liquid Propane (LP) and Natural Gas (NG). The difference between LP and NG Warming Trends burners are the “jets”. If, down the road, you need to convert from LP to NG or vice-versa, you can do so by purchasing replacement jets from us at $25 each.
Propane – pros
Propane – cons
Natural Gas – Pros
Natural Gas – Cons
Even though the standard key valve inlet is 3/4″, you may need a larger gas line to span long distances.
In order to get the proper volume and pressure of fuel, you need a gas line that is large enough in diameter to carry it sufficiently. For the most accurate assessment, consult a fuel professional. For a rough estimate, utilize our gas line sizing charts below.
*Make sure the BTUs from your line can supply at least 60-70% of what the burner is rated at. (At 60% capacity, your flame height may be more like 18″ high vs. 24″+ at full capacity.)
Gas line sizing variables
You can have great gas pressure, but if your line is too small, you may not get the desired flame. Think about it like filling up a swimming pool. If you reduce the nozzle size significantly, you may have a ton of pressure, but it’s going to take longer to fill up the pool. You need both pressure and volume to get a great flame. This is why the size of the gas line is so important.
Now that you understand the importance of volume (BTUs), let’s talk pressure.
Optimal Pressure for Crossfire burners:
Water Column is the term used to measure pressure. There are 27.7 inches of water column pressure in 1 PSI of pressure. So 7″wc is about 1/4 PSI. This is the normal pressure that household natural gas is delivered.
The device used to measure pressure of this type is called a Manometer
Pressure too High? You may experience unwanted noise, usually a hissing sound. You might also find it difficult to dial in the desired flame height using the key valve.
Pressure too Low? The flame will not be as tall and hot
Location of Gas Stub
You DO NOT need an air mixer with any of our burners. Air is mixed at each jet.
LP Regulators
NG Regulators
Standard 20lb Tank
40lb Tank
High Volume Tanks
Hiding the Tank
Gas Consumption
Compliance with the following standards:
Massachusetts
Effective May 5, 2021 over 100 Warming Trends CROSSFIRE burners will be approved for use in Massachusetts.
All gas products approved for use can be found on the Massachusetts Consumer Affairs and Business Regulation (OCABR) website: Office of Consumer Affairs and Business Regulation (OCABR). To confirm the approval of a product, simply:
Click “Find Products” and see the listing of accepted products.
*A burner plate or pan is required for use of any ignition system other than match lit.
The main purpose of the plate or pan is to hold in the media (lava rock, glass, etc). It also acts like the hood of a car, in that it can be lifted up and out in order to access the gas line or key valve underneath. The plate/pan makes installation easier as well.
What’s it made of?
Is a plate/pan ALWAYS necessary?
Plate (No Sidewalls)
Pans (2″ or 3″ Sidewalls. 2″ is Standard.)
Drop-In Pans (2″ or 3″ Sidewalls + 1″-2″ Lip)
Does the plate attach to the burner?
There are many methods to mount a plate/pan inside your fire feature. We’re just going to tell you our favorite way to do things because… well, it has worked well so far! With that being said, these methods may not work in all situations, so put your problem-solving hat on and get creative.
*Complete & RTF Systems: you won’t need to worry about plate/pan mounting; they’re designed for simplicity
Mounting the Plate/Pan
Plate/Pan Depth
If your fire feature is already built and you can’t use a standard sized plate, you have a few options:
Cut your plate to size on-site
Make your plate bigger
Order a Custom Size
*TIP: Give yourself about 1/2″ of space around the plate so that it’s easy to insert into the fire feature opening
(Recommended)
Enables easy flame height adjustment as well as the ability to turn the gas on or off. All flex lines are stainless steel and whistle free.
FK1
FK2
Recommended Ventilation
Details
Lighting Instructions
Recommendations
Operation
Installation
Push Button Ignition Kit + Mounting Bracket
Dimensions of bracket:
*This unit carries no warranty. Please be aware that this system requires a very precise placement of the spark rod in relation to the burner jet. Any movement or blockage of the spark will restrict the ignition from working properly. In these cases a conventional lighter can be used to ignite your fire.
Installation
Details:
How to operate (video)
Requirements
Installation
Description
The Platinum Automatic Ignition System delivers superior quality, performance, and value. Expertly engineered, this innovative ignition has been designed and built to be the safest and most dependable way to light fire in both residential and commercial spaces.
Features
Tracking information is emailed to you once it becomes available. Order status updates are often not available until production is complete. Thank you for your patience!
Venture/Arbor Series (Metal/wood):
Gather Series (Concrete):
Transit time not included. Expect 1-2 weeks for the shipment to arrive.
Please add products to your cart and enter your address at checkout to see detailed shipping costs
*Free Shipping: Applies to most orders over $199 in the continental U.S. with the following exceptions:
*Shipping to Canada: You may be charged additional border fees and taxes when you receive your product. Montana Fire Pits is not responsible for those fees.
*Please add products to your cart and enter your address to see more information on shipping costs to Canada, Hawaii, and Alaska
