Specialty & Custom Burners

Fit a powerful gas burner in any shape or size. Get creative! Complete with all-brass construction, a limited-lifetime warranty, and twice the flame as standard stainless steel burners.

Custom Quote Request - Burners, Plates, Pans

For when standard sizes or shapes won't work for your project

"*" indicates required fields

Location*
Fuel Type*
Enter Length x Width (or Diameter) in INCHES. This is the burn area; the inside dimensions of the fire pit where the burner/plate will go.
Shape*
Preferred Burner Style*
Plate/Pan*
Plates are most common and work great for most projects. Standard pans have 2" sidewalls and are great when your top cap overlaps into your opening. Drop in pans have 2" sidewalls and 1" lip standard, but you can specify sidewalls 2"-4" and a lip 1" - 2". If you would like dimensions other than standard, please enter them in the "Additional Details" field at the end of the form.
Flex Line and Key Valve Kit*
Ignition*
For electronic ignition, the pilot assembly needs something to mount to, such as a plate or pan. If you do not want a plate or pan, ignition will come in a box and the warranty is void. If you do opt for a plate or pan, the ignition will be mounted in the factory for easy install. Electronic ignition gas box can be located up to 10' away from the burner, and the electrical box can be located up to 150' from the burner.
Flat Aluminum Cover*
If you have them, help our designers see your project
Drop files here or
Accepted file types: jpg, gif, png, pdf, Max. file size: 10 MB.

    Top Fuel Answers

    There are various pros/cons of Liquid Propane (LP) and Natural Gas (NG). The difference between LP and NG burners that we carry are the “jets”. If, down the road, you need to convert from LP to NG or vice-versa, you can do so by purchasing replacement jets from us at $25 each. 

    Propane – pros

      • Flexibility/portability
      • Opens up new location possibilities
      • Sometimes NG is not available

    Propane – cons

      • More expensive to burn than NG
      • Heavier than air, so it sinks down. This makes ventilation more important.
      • Requires refilling the tank
      • Hiding the propane tank can present new aesthetic challenges
      • Black soot tends to build up faster on fire media such as ceramic logs and cannonballs (it can be cleaned off)

    Natural Gas – Pros

      • Cheaper to burn; you probably won’t even notice an increase in your gas bill
      • You won’t run out, so burn to your heart’s content without the dreaded “we’re out of gas”
      • Since it’s lighter than air and rises, there’s less likelihood of unwanted fuel accumulation in the vessel
      • Slightly cleaner burning; less soot build up

    Natural Gas – Cons

      • Limited to what’s available in your area
      • May require upgraded meter or larger diameter fuel lines to provide adequate BTUs
      • The volume and pressure can be affected by other appliances
      • Might require a longer gas line, depending on where your fire feature will live  
      • Would be difficult to change the fire feature’s location after installation
      • Check the side of your gas meter for a BTU rating. Most commonly they are rated at 250K BTUs

    In order to get the proper volume and pressure of fuel, you need a gas line that is large enough in diameter to carry it sufficiently. For the most accurate assessment, consult a fuel professional. For a rough estimate, utilize our gas line sizing charts below. 

    *Make sure the BTUs from your line can supply at least 60-70% of what the burner is rated at.

    Propane Gas Line Sizing Chart

    Natural Gas Line Sizing Chart

    Gas line sizing variables

      • Using angled couplings can reduce the volume/flow of fuel
      • Adding a 90 degree angle in your line adds the equivalent of 5 feet of distance
      • Running different sized lines over various distances is acceptable, but for maximum fuel volume, run larger lines over long distances
      • Number of appliances, whether it’s a dedicated line or not; all these factors play a role in volume and pressure
      • Pro Tip: if you haven’t installed your gas line yet, consider running it in conduit so that if you ever need to repair or change it, you won’t have to dig it up

    You can have great gas pressure, but if your line is too small, you may not get the desired flame. Think about it like filling up a swimming pool. If you reduce the nozzle size significantly, you may have a ton of pressure, but it’s going to take longer to fill up the pool. You need both pressure and volume to get a great flame. This is why the size of the gas line is so important. 

    Now that you understand the importance of volume (BTUs), let’s talk pressure. 

    Optimal Pressure:

    • LP: 11-13″ water column (w.c.)
    • NG: 7-10″ water column (w.c.)

    Water Column is the term used to measure pressure. There are 27.7 inches of water column pressure in 1 PSI of pressure. So 7″wc is about 1/4 PSI. This is the normal pressure that household natural gas is delivered.

    The device used to measure pressure of this type is called a Manometer

    Pressure too High? You may experience unwanted noise

    Pressure too Low? The flame will not be as tall and hot

     

     

    Location of Gas Stub

    • Can be off-center or on-center, depending on the size of your fire feature
    • The key valve is generally located on the side of the fire pit, so if it makes sense for your build, place the gas stub off-center to reduce the distance of gas stub to key valve
    • Instruct the contractor to keep the gas stub as low as possible to make room for electronic ignition, or in the case that the plate sets fairly low
    • On some builds, the plate sits only 8″ off the ground

    You DO NOT need an air mixer with any of our burners. Air is mixed at each jet. 

    LP Regulators

      • For optimal regulation for burners over 200K BTUs, contact a local propane supplier
      • For regulators 200K BTUs or lower, CLICK HERE
      • From the tank, propane is HIGH PRESSURE, so it must be regulated down, because the burners are low pressure
      • For longer gas lines, we often use a high pressure (10psi) regulator at the tank end, and a “2nd stage” regulator on the other end of the line to bring the pressure to 11-13″wc

    NG Regulators

      • Consult a professional (plumber/HVAC)

    Standard 20lb Tank

    • A standard 20lb/5 gallon BBQ propane tank can be used for burner systems 180K BTUs and under
    • The FIRE CUBE is a complete unit that can have a self-contained propane tank
    • Burn time varies from 6-12 hours, depending on how hot you run it
    • Results may vary, and it is common for the fuel to “freeze up” with burners 180K BTUs and up. What that means is that after 45 minutes or so, the flame only goes to about half. Remedy this by using two tanks connected together

    40lb Tank

    • This is a better option for most of our burners from 100K to 200k BTUs
    • It will give you longer burn times
    • Still relatively small and easy to move

    High Volume Tanks

    • Contact your local propane supplier

    Hiding the Tank

    • You can always run a larger diameter line and hide the tank in an inconspicuous location
    • You can purchase 20lb propane tank covers that make hiding the tank a cinch

    Gas Consumption

    • All of our burners burn with incredible efficiency due to the engineered jets. They mix fuel and oxygen at the flame which makes it taller, brighter, and hotter using less fuel
    • Read all about how much fuel you might be burning at full capacity – Learn More

    Calculate HERE

    *Note: our burners will burn with more efficiency than others because of the proprietary jets

    Compliance with the following standards:

    • ANSI Z21.97/CSA 2.41 Outdoor Decorative Gas Appliances
    • The burner system is certified nationally, however, it is up to the customer or contractor to verify local requirements

    Certified Burners

    Massachusetts

    Effective May 5, 2021 over 100 Warming Trends CROSSFIRE burners will be approved for use in Massachusetts. 

    All gas products approved for use can be found on the Massachusetts Consumer Affairs and Business Regulation (OCABR) website: Office of Consumer Affairs and Business Regulation (OCABR). To confirm the approval of a product, simply:

    1. Visit the OCABR website.
    2. Select “Product Information” from the drop down, then click “Go.”
    3. Enter Product information.
      1. Select “Gas” 
      2. Manufacturer: Warming Trends, LLC
      3. Model Number: Enter the burner type and BTU output (i.e. CFB180, CFBT290, CFBO140) If you do not have the model information, you may search using only the manufacturer name to bring up all Warming Trends burners that are accepted. 

    Click “Find Products” and see the listing of accepted products. 

    Canadian Customers

    Most metropolitan areas in Canada will require an automatic shutoff for fire pits over 65K BTUs in order to get a permit or certification.

    • Our Premium Electronic Ignition system has the proper fuel and flame censors to automatically shut down the fire when needed. Combine it with a dial timer to increase safety and ease. 
    • You can still purchase higher BTU burners without the premium ignition, and we will ship it with a fitting that limits the burner to 65K BTUs in the case that you’d like to have it certified.

     

    Choosing the Right Size

    Use these measurements as a good starting point for your designing and planning. 

    Master Reference Guide 

    Round & Square standard opening sizes

    • 18″, 24″, 30″, 36″, 42″, 48″, 60″
    • Add .5″ to 1″ to your opening to make room for the plate

    Rectangular standard opening sizes

    • See H-STYLE and TREE-STYLE burner pages and use the Plate sizes to determine standard opening sizes
    • Add .5″ to 1″ to your opening to make room for the plate

    Ideal ledge width to set drinks on, put feet up on, etc…

    • 7″ to 12″

    How deep to mount the plate:

    • 3″ to 5″ (plate to top of burner jet is 3″)

    Clearance from fire to:

    • Top ledge: 5″-6″
    • Combustible building/wall: 36″
    • Combustible ceiling/overhang: 10′

    Click image below for a visual clearance guide

    Burner/Plate/BTU size reference – Click Here

    Shape & Size

      • Square, Round, Rectangular, Custom
      • Standard Round & Square Opening sizes
        • 18″, 24″, 30″, 36″, 42″, 48″, 60″

    Do you need a plate/pan?

      • See PLATES & PANS to help answer this question
      • If YES, choose a burner that has a plate size that works with your opening
      • If NO, make sure you keep 5-6″ of clear space around the burner so that the heat doesn’t harm your top
      • Custom cut plates are available

    This part is simple: just make sure your gas line can supply at least 60-70% of what the burner is rated at.

    Example: 

    • Desired Burner: 180K BTUs
    • Minimum Required Fuel Volume: at least 108K BTUs

    How Hot?

    • All of the burners we carry are HOT
    • All Crossfire models have the same “jets”; providing hotter, brighter, taller flames

    Why do Warming Trends burners have so many more BTUs than others?

    • The secret is in the jets (no, you can’t just buy the jets. Nice try!)
    • Other burners are made by poking small holes in stainless steel tubes. Gas just seeps out without mixing oxygen. The flame is small and not as hot or controlled, hence the smaller BTU ratings
    • Going with a stainless steel burner greatly increases the risk of being bummed with your fire 🙁
    • Crossfire burners produce twice the amount of flame with the same amount of fuel as conventional stainless steel burners

     

    Almost everyday we get inquiries like this: “I have a fire pit with a stainless steel burner but I’m not happy with the flame. It’s only 5″ high and it doesn’t put out any heat. What can I do?”

    This is the reason why we ONLY carry Warming Trends Crossfire brass burners; because we don’t want to have that difficult conversation with our customers. If you have an adequate fuel supply, you WILL be satisfied with our burners!

    You may pay more upfront for all brass, but you will pay less over time for these reasons:

    • Brass does not corrode over time like stainless steel
    • You won’t feel the need to “upgrade” to get a better flame… you will already have THE BEST
    • Limited LIFETIME warranty! 
    • Twice the flame

    WARMING TRENDS SPECIALTY BURNERS

    These specialty gas burners are exactly the unique style of fire pit burner you’ve been looking for. Circular designs and customizable centipede style burners will add the finishing touch to your custom fire feature. We’ve added the convenient option to include a flex valve kit (flex line, key valve, and key) as well as an aluminum burner plate at checkout. Get everything you need to set-up your fire feature all in one purchase.

    Our specialty natural gas fire pit kit burners come in a variety of styles.  Whatever your gas fire pit needs, we have a burner that can work for you. If you find the process of choosing fire pit accessories daunting, we also provide a free buying guide that can provide the information you need to be confident in your buying decisions. We sell full gas fire pit kit burners and accessories so you’ll have everything you need to get your fire pit up and running. For more information on our natural gas and propane fire pit kit and burners, contact us today.

      0
      Your Cart
      Your cart is emptyReturn to Shop

          Before you Buy

          *IMPORTANT*

          Concrete/GFRC fire features WILL develop charring and non-structural cracking, aka hairline cracks. This is the nature of concrete and thus, not covered by warranty.

          Hairline Cracks & Charring Will Occur

          Nearly ALL concrete fire pits, whether sold by Montana Fire Pits or others, will eventually develop the same characteristics of browning/charring AND hairline cracks. The cracks can appear anywhere on the concrete shell, but are most prominent on the inside ledges nearest the fire. Visibility of the hairline cracks has been known to diminish when the unit is dry. The cracks will re-appear when any moisture is present. These characteristics can develop as soon as 20 minutes after lighting the fire. 

          Montana Fire Pits does not provide warranty coverage for cracking, charring/browning, or chipping of a concrete vessel.

          Exceptions:

          Shipping damage that has been properly photographed and documented by the receiver, as well as submitted to Montana Fire Pits within 3 days of delivery, OR ideally the shipment is refused, will be considered for a freight claim based on evidence provided by you, the customer or receiver.

          Considerations: Ways to Minimize Cracking and Charring

          • Do not use the fire in windy conditions. Windy conditions cause the flame to lay over and come in contact with the concrete.
          • Do not burn on high for more than 15 minutes, especially in windy conditions. 
          • Consider glass flame guards. The guards may help reduce the risk of the fire charring the inside edge of the burn area. There is no guarantee this will remedy the cracking and charring.  
          • Consider an alternative material for the fire vessel. We recommend steel and aluminum for the most durability. These materials are unaffected by the fire. You can burn on high for long periods of time without charring the metal. Soot may build up, but it wipes off with mild soap and a soft cloth. 

          If you wish to proceed with a concrete fire system, we’ll send you a document to sign which is your acknowledgement that the warranty does not cover cracking, charring, or chipping. 

          Fire Pit Cover Guide

          Tabletop Cover Options

          Note: Most tabletop covers that are larger than 48″ are fabricated in 2 or more pieces for ease of handling.

          The Advantage of Arbor Wood

          We at Montana Fire Pits have a favorite when it comes to covers; introducing our very own hand-made Arbor Wood Covers. They elevate a fire system to new levels in regards to aesthetics, as well as functionality. 

          • Thermally modified lumber allows natural wood to last 30+ years
          • You can let it weather into a beautiful gray tones, or easily re-apply protective oil at anytime to enjoy the dark, rich colors
          • Lighter and easier to carry compared to steel covers
          • Create a very inviting and functional tabletop experience
          • Recommended Clear Oil: Cutek Stain Extreme
          • Purchase ARBOR WOOD

          Covering the Burn Area

          • Best practice is to cover at least the burn area when not in use
          • This keeps water and debris out of the components
          • If you consistently cover your Crossfire burner, you enjoy the peace of mind of a lifetime warranty

          Covering Edge to Edge

          • Covering the entire top of the fire system is a great design option
          • Creates a very uniform appearance
          • Especially fitting for when your top ledge is 5″ or narrower
          • Optional: make the dimensions 2″ larger than the fire pit for a different look

          Adding Sidewalls: the Raised Cover

          • Available with our hand-built Arbor Wood Covers
          • When you want fire media that mounds up, such as cannonballs or logs, a cover with sidewalls might be for you
          • Determine how high your fire media might be
          • In rectangle fire systems, fire media tends to mound up a little less, and so we recommend 5″ sidewalls 
          • For round fire systems which tend to have higher fire media, we recommend 8″ – 10″ sidewalls 
          • Keeps the finish clean
          • Great for covering fire pits with stacked up fire media over 5 inches, such as with gas logs
          • Not considered necessary if you have a tabletop cover
          • You may consider it for harsh winters, prolonged sunlight

          If you desire a soft cover, we recommend that you purchase your SOFT COVER after your fire pit is installed and your fire media is chosen.

          Understanding Materials and Applications

          Steel

          • Lowest cost option when purchased with a steel fire system
          • Sits flush within the burn area for a perfect fit
          • Flawless color match
          • Disadvantage: it’s heavy, can be mildly difficult to place on the fire system

          Aluminum

          • Lighter than steel
          • Great for concrete, ready to finish kits, paver fire pits, etc…
          • Can be powder coated or raw/brushed
          • When ordered with a concrete system, aluminum covers will be built to fit within the burn area ledge for a flush interface

          Arbor Wood

          • Beautiful and authentic
          • Easy to handle
          • Very low maintenance
          • Extremely long-lasting
          • Editor’s pick BEST fire pit cover

          Congratulations!

          You have reached our top status… Pro Solutions Platinum. Enjoy our best pricing.

          Free shipping applies to most orders over $99 in the continental U.S.

          Tax Exemption: If you have documents to prove exemption from your state sales tax, visit YOUR ACCOUNT and click on “Tax Exemption”.

          Contact Us

          Mon – Fri: 9am – 4:30pm MST

          Sat – Sun: Closed

          Online Contact

          Call (833) 228-5244

          Chat (coming soon)

          Your Active Discounts

          Discounts will be automatically applied to your cart.

          Free shipping applies to most orders over $99 in the continental U.S.

          Tax Exemption: If you have documents to prove exemption from your state sales tax, visit YOUR ACCOUNT and click on “Tax Exemption”.

          Contact Us

          Mon – Fri: 9am – 4:30pm MST

          Sat – Sun: Closed

          Online Contact

          Call (833) 228-5244

          Chat (coming soon)

          Quick Contact

          Expert advice comes standard

          Mon – Fri: 9am – 4:30pm MST

          Sat – Sun: Closed

          Online Contact

          Call (833) 228-5244

          Chat

          Manuals & PDFs

          Your local gas professional (plumber, HVAC, propane supplier, etc…) needs to know these requirements

          1. BTU rating of the burner 
          2. Fuel Pressure recommended at the Burner
            • Natural Gas: 7″ Water Column
            • Propane: 11″ Water Column

          Fuel Requirements

          Your local gas professional (plumber, HVAC, propane supplier, etc…) needs to know these requirements

          1. BTU rating of the burner (read more under “Gas Line Sizing”)
          2. Fuel Pressure recommended at the Burner
            • Natural Gas: 7″ Water Column
            • Propane: 11″ Water Column

          There are various pros/cons of Liquid Propane (LP) and Natural Gas (NG). The difference between LP and NG Warming Trends burners are the “jets”. If, down the road, you need to convert from LP to NG or vice-versa, you can do so by purchasing replacement jets from us at $25 each. 

          Propane – pros

            • Flexibility/portability
            • Opens up new location possibilities
            • Sometimes NG is not available

          Propane – cons

            • More expensive to burn than NG
            • Heavier than air, so it sinks down. This makes ventilation more important.
            • Requires refilling the tank
            • Hiding the propane tank can present new aesthetic challenges
            • Black soot tends to build up faster on fire media such as ceramic logs and cannonballs (it can be cleaned off)

          Natural Gas – Pros

            • Cheaper to burn; you probably won’t even notice an increase in your gas bill. Clients of ours have reported $0.25 – $0.75 per hour
            • You won’t run out, so burn to your heart’s content without the dreaded “we’re out of gas”
            • Since it’s lighter than air and rises, there’s less likelihood of unwanted fuel accumulation in the vessel
            • Slightly cleaner burning; less soot build up

          Natural Gas – Cons

            • Limited to what’s available in your area
            • May require upgraded meter or larger diameter fuel lines to provide adequate BTUs
            • The volume and pressure can be affected by other appliances
            • Might require a longer gas line, depending on where your fire feature will live  
            • Would be difficult to change the fire feature’s location after installation
            • Check the side of your gas meter for a BTU rating. Most commonly they are rated at 250K BTUs

          Even though the standard key valve inlet is 3/4″, you may need a larger gas line to span long distances.

          In order to get the proper volume and pressure of fuel, you need a gas line that is large enough in diameter to carry it sufficiently. For the most accurate assessment, consult a fuel professional. For a rough estimate, utilize our gas line sizing charts below. 

          *Make sure the BTUs from your line can supply at least 60-70% of what the burner is rated at. (At 60% capacity, your flame height may be more like 18″ high vs. 24″+ at full capacity.)

          Propane Gas Line Sizing Chart

          Natural Gas Line Sizing Chart

          Gas line sizing variables

            • Using angled couplings can reduce the volume/flow of fuel
            • Adding a 90 degree angle in your line adds the equivalent of 5 feet of distance
            • Running different sized lines over various distances is acceptable, but for maximum fuel volume, run larger lines over long distances
            • Number of appliances, whether it’s a dedicated line or not; all these factors play a role in volume and pressure
            • Pro Tip: if you haven’t installed your gas line yet, consider running it in conduit so that if you ever need to repair or change it, you won’t have to dig it up

          You can have great gas pressure, but if your line is too small, you may not get the desired flame. Think about it like filling up a swimming pool. If you reduce the nozzle size significantly, you may have a ton of pressure, but it’s going to take longer to fill up the pool. You need both pressure and volume to get a great flame. This is why the size of the gas line is so important. 

          Now that you understand the importance of volume (BTUs), let’s talk pressure. 

          Optimal Pressure for Crossfire burners:

          • LP: 11″ water column (w.c.)
          • NG: 7″ water column (w.c.)

          Water Column is the term used to measure pressure. There are 27.7 inches of water column pressure in 1 PSI of pressure. So 7″wc is about 1/4 PSI. This is the normal pressure that household natural gas is delivered.

          The device used to measure pressure of this type is called a Manometer

          Pressure too High? You may experience unwanted noise, usually a hissing sound. You might also find it difficult to dial in the desired flame height using the key valve.

          Pressure too Low? The flame will not be as tall and hot

          Location of Gas Stub

          • Most commonly the gas stub is positioned underneath the fire feature so that you don’t see it
          • It can be off-center or on-center, depending on the size of your fire feature
          • You may want to go off-center if you’re using electronic ignition
          • The key valve is generally located on the side of the fire pit, so if it makes sense for your build, place the gas stub off-center to reduce the distance of gas stub to key valve
          • Most often, the plumber will use hard pipe to connect from the gas stub to the key valve. However, if they decide to use a flexible line, most lines are 36″ long, so it makes sense to try and keep the gas stub within 36″ from the key valve location
          • Instruct the contractor to keep the gas stub as low as possible to make room for electronic ignition, or in the case that the plate sets fairly low
          • On some builds, the plate sits only 8″ off the ground

          You DO NOT need an air mixer with any of our burners. Air is mixed at each jet. 

          LP Regulators

            • For optimal regulation for burners over 250K BTUs, contact a local propane supplier
            • For regulators 250K BTUs or lower, purchase our REGULATOR KIT
            • From the tank, propane is HIGH PRESSURE, so it must be regulated down, because the burners are low pressure
            • For longer gas lines, we often use a high pressure (10psi) regulator at the tank end, and a “2nd stage” regulator on the other end of the line to bring the pressure to 11-13″wc

          NG Regulators

            • Consult a professional (plumber/HVAC)

          Standard 20lb Tank

          • A standard 20lb/5 gallon BBQ propane tank can be used for burner systems 180K BTUs and under
          • The Canyonlands Fire Table is a complete unit that can have a self-contained propane tank
          • Burn time varies from 6-12 hours, depending on how hot you run it
          • Results may vary, and it is common for the fuel to “freeze up” with burners 180K BTUs and up. What that means is that after 45 minutes or so, the flame only goes to about half. Remedy this by using two tanks connected together

          40lb Tank

          • This is a better option for most of our burners from 100K to 200k BTUs
          • It will give you longer burn times
          • Still relatively small and easy to move

          High Volume Tanks

          • Contact your local propane supplier

          Hiding the Tank

          • You can always run a larger diameter line and hide the tank in an inconspicuous location
          • You can purchase 20lb propane tank covers that make hiding the tank a cinch

          Gas Consumption

          • All of our burners burn with incredible efficiency due to the engineered jets. They mix fuel and oxygen at the flame which makes it taller, brighter, and hotter using less fuel
          • Read all about how much fuel you might be burning at full capacity – Learn More

          Compliance with the following standards:

          • ANSI Z21.97/CSA 2.41 Outdoor Decorative Gas Appliances
          • The burner system is certified nationally, however, it is up to the customer or contractor to verify local requirements

          Certified Burners

          Massachusetts

          Effective May 5, 2021 over 100 Warming Trends CROSSFIRE burners will be approved for use in Massachusetts. 

          All gas products approved for use can be found on the Massachusetts Consumer Affairs and Business Regulation (OCABR) website: Office of Consumer Affairs and Business Regulation (OCABR). To confirm the approval of a product, simply:

          1. Visit the OCABR website.
          2. Select “Product Information” from the drop down, then click “Go.”
          3. Enter Product information.
            1. Select “Gas” 
            2. Manufacturer: Warming Trends, LLC
            3. Model Number: Enter the burner type and BTU output (i.e. CFB180, CFBT290, CFBO140) If you do not have the model information, you may search using only the manufacturer name to bring up all Warming Trends burners that are accepted. 

          Click “Find Products” and see the listing of accepted products. 

          Canadian Customers

          Most metropolitan areas in Canada will require an automatic shutoff for fire pits over 65K BTUs in order to get a permit or certification.

          • Our Premium Electronic Ignition system has the proper fuel and flame censors to automatically shut down the fire when needed. Combine it with a dial timer to increase safety and ease. 
          • You can still purchase higher BTU burners without the premium ignition, and we will ship it with a fitting that limits the burner to 65K BTUs in the case that you’d like to have it certified.

           

          Plates and Pans

          *A burner plate or pan is required for use of any ignition system other than match lit.

          The main purpose of the plate or pan is to hold in the media (lava rock, glass, etc). It also acts like the hood of a car, in that it can be lifted up and out in order to access the gas line or key valve underneath. The plate/pan makes installation easier as well.

          What’s it made of?

          • Aluminum
          • Aluminum does not rust

          Is a plate/pan ALWAYS necessary?

          • No, in some cases a plate/pan is not necessary
          • You may decide to fill up the space with some gravel or lava rock and set the burner on that instead of a plate or pan
          • Using a plate/pan is the most convenient for installation and maintenance

          Plate (No Sidewalls)

          • Appropriate for most builds
          • Sidewalls are not necessary when the burner is in the common position- recessed 3-5 inches below the finished top
          • Use stacked cinder blocks, bricks, or pavers under the plate. This makes for a simple and sturdy plate mount

          Pans (2″ or 3″ Sidewalls. 2″ is Standard.)

          • If the top of your fire table overlaps, or encroaches into your opening, and its thickness is less than 3 inches, you may want a pan instead of a plate (since the pan has to be smaller than the smallest part of the inside diameter) 
          • The sidewalls help contain the fire media/lava rock

          Drop-In Pans (2″ or 3″ Sidewalls + 1″-2″ Lip)

          • Sometimes necessary if you plan on building a portable fire feature and aren’t able to stack up blocks under the plate
          • Bar-height or uncommon builds might benefit from a drop-in pan
          • You will see a brushed aluminum metal band on the top of your fire feature when you use a drop in pan
          • Drop-in pans are available as a custom order – CLICK HERE
          • We recommend 3″ sidewalls with a 1.5″ lip in most cases

          Does the plate attach to the burner?

          • In most cases, yes
            • When you order a package from us, most of the time it will come with a threaded piece welded on to the plate/pan
            • The burner screws onto it
            • It’s very simple to remove or attach the burner (righty-tighty, lefty-loosy… make sure to re-apply pipe dope/tape!)
          • It’s not required that the burner attaches to the plate/pan. You can set the burner directly on the plate/pan. This will reduce the height of the burner by 3/4″. This might be beneficial if you want to cover your fire feature with a flat cover

          There are many methods to mount a plate/pan inside your fire feature. We’re just going to tell you our favorite way to do things because… well, it has worked well so far! With that being said, these methods may not work in all situations, so put your problem-solving hat on and get creative.

          *Complete & RTF Systems:  you won’t need to worry about plate/pan mounting; they’re designed for simplicity

          Mounting the Plate/Pan

          • Consider stacking up cinder blocks, bricks, or pavers inside the fire feature cavity
          • Place the plate/pan directly on the blocks
          • Adjust the block height by either adding some fill, or by digging underneath
          • Most commonly, plates/pans are mounted 4″-5″ below the finished top of the fire feature

          Plate/Pan Depth

          • 4-5″ below the finished top is recommended
          • Recessing it deeper may make the fire seem smaller, and you won’t see the media as well
          • Recessing it to be more shallow can give it a “proud” look; where all the parts stick up high and make a statement. Though you may have to ‘mound’ the fire media up higher in order to cover the jets. It’s not a bad look, but you won’t be able to use a flat metal cover if that’s your desire.
          • The depth at which the plate sits is really up to you. Keep in mind, the burner sits 3″ high from plate to the tip of the jet

          If your fire feature is already built and you can’t use a standard sized plate, you have a few options:

          Cut your plate to size on-site

            • Use a jig-saw with metal blade, or a grinder wheel with cutoff
            • It’s 3/16″ aluminum and your cut doesn’t need to look pretty

          Make your plate bigger

            • Use concrete board to extend the size of the plate
            • Watch THIS VIDEO to get an idea

          Order a Custom Size

          *TIP: Give yourself about 1/2″ of space around the plate so that it’s easy to insert into the fire feature opening

          Determining What You Need

          (Recommended)

          Enables easy flame height adjustment as well as the ability to turn the gas on or off.  All flex lines are stainless steel and whistle free.

          FK1

          • For use with any 121K – 249K BTU Burner
          • Kit Includes: (1) 36” L x 3/4” Diameter Flex Line + (2) 3/4″ Flared Fittings + 3/4” Key Valve + 3” and 12” Key + 1/2” x 2” Nipple

          FK2

          • For use with any burner 300K+ BTU
          • Kit Includes: (2) 36” L x 3/4” Diameter Flex Lines + (4) 3/4″ Flared Fittings + 3/4” Key Valve + 3” and 12” Key + (2) 3/4” x 3” Nipple + (2) 3/4” Tee + (1) 3/4” x 1/2” MM Reducer Fitting
          FKM1 – Specific to the Mercury Ignition. Allows fuel connection from the ignition to the burner.
          • If the walls of your fire pit are thick, you may need this accessory
          • Closes the gap from the key valve to the decorative faceplate (escutcheon)
          • Can also be made onsite with hard pipe or sprinkler pipe to the length that you need

          Vent Kit

          Recommended Ventilation

          • 18 square inches on opposing sides (for cross-breeze)
          • Keep the vents lower towards the ground
          • Dimensions: 3 7/8″ x 12″

          Ignition Types

          Installation of Ignition

          • A burner plate or pan is required for any ignition system other than match lit.
          • If you have your own plate or pan, you will need to drill a hole in it for the mounting of the ignition pilot/spark rod.
          • The Mercury Ignition has a 250,000 BTU limitation.
          Platinum Ignition System by Warming Trends gas fire pit ignition types

          *NEW* Platinum Ignition System

          Installation: Comes pre-installed to the plate/pan unless ordered a la carte. This allows for a hassle-free setup. Electrical required.

          The Platinum Automatic Ignition System delivers superior quality, performance, and value. Expertly engineered, this innovative ignition has been designed and built to be the safest and most dependable way to light fire in both residential and commercial spaces.

          • Light your fire with the flip of a switch, remote, home automation, or dial timer.
          • Clean design with no need for any components to be attached to the outside of your fire feature.
          • Auto shutoff for the ultimate safety + fully certified.
          • Made in the U.S.A.
          • 680,000 BTUs of gas output 
          • Unique wind cage design that provides true protection to the pilot components from wind and rain.
          • Customized ignition settings allow for better performance and reduces cycling faults.
          • Robust components provide reliability and durability.
          • LED-based diagnostics provide quick and easy troubleshooting.
          • Design allows for field serviceability.
          • Coupled with the Warming Trends’ WATERSTOP™ fitting provides unmatched protection of the ignition from water and debris. 
          • Warranty: 3 years for residential, 1 year for commercial (burner must be covered when not in use or warranty is null and void)
          • Electrical is required
          • Commonly used is a standard 110 volt GFI outlet located underneath the fire pit
          • For product support, please contact Warming Trends at 303-346-2224

          Mercury Ignition (Battery Powered)

          Installation: Comes pre-installed to the plate/pan unless ordered a la carte. This allows for a hassle-free setup. Powered by (2) AA batteries.

          Mercury Ignition Spark Igniter with Internal Safety Shutoff + 3 FT Pilot for use up to 240K BTU

          • Added safety of auto fuel shutoff
          • Great for commercial spaces or if non-homeowners desire to light the fire
          • Pilot assembly comes pre-mounted to the plate
          • Only available with burner and plate combo orders or the Venture Series
          • No key valve required
          • View INFORMATION PDF

          Watch how the Mercury works…

          Play Video

          Match Lit (Most Common)

          • To light, turn your fuel valve (most commonly a key valve supplied by us) to a low volume
          • Use a lighter or match to ignite the flame manually
          • Gradually turn up the key valve so that the other jets light
          • Not recommended for kids or VRBO/Rentals

          Installation: hole for the spark rod is pre-drilled in the plate/pan unless ordered a la cart.

          Push Button Ignition Kit + Mounting Bracket

          • Powered by a AA battery
          • Holds a key valve as well as button module
          • To light, turn the key and press spark button until lit
          • Will work with any size burner, but for large burners over 350,000 BTUs, we recommend the Platinum Ignition
          • The bracket allows for more mounting options
          • Can be used in place of a paver
          • Should be combined with a Key Valve/Flex line kit

          Dimensions of bracket:

            • Width: Adjustable 8″-12″
            • Height: 3 7/8″ 
            • Depth: 5″

          Push Button Battery Operated Control Module + Spark Igniter Rod and Wire

          • AA Battery operated
          • Spark rod is mounted to the plate
          • Spark rod must be within very close proximity to a jet on the burner
          • To light, turn the key valve (separate product) to get gas flow going and press button until spark ignites the fuel
          • Without a mounting bracket, the button most commonly mounts to a metal fire pit

          Holiday Deals🎄

          Reduced Prices & Free Lava Pebbles w/ Select Models

          Hours
          Minutes
          Seconds

          Enter Code at Checkout:

          Subscribe & Save 5%!

          This field is for validation purposes and should be left unchanged.

          givethanks2024

          Limited stock… Order Today!

          Here’s what you get…

          Subscribe and receive a discount code and use it even on sale items!

          Available with purchase of Venture & Arbor collections, or Fast Ship inventory.

          Orders over $99, lower 48 states.

          If you see a lower price from MFP before the year ends, we’ll refund you the difference!

          Use code at checkout:

          SAVE5

          Days
          Hours
          Seconds

          Save 5% Today

          +Free Nationwide Shipping

          By signing up, you agree to receive occasional emails from Montana Fire Pits. You can unsubscribe anytime by clicking the link at the bottom of an email. 

          Prices are Changing

          Beginning February 1st, 2023

          Prices for our products will increase about 3% starting on February 1st. As always, with Montana Fire Pits you’ll enjoy:

          • Products made in the U.S.A
          • Highest quality materials and design
          • High customer satisfaction ratings
          • The best fire in the industry

          Thank you for considering Montana Fire Pits!

          MFPbadgeColor

          Lead Times

          • Most of our products are hand-made to order in the U.S.
          • Delays in production are rare, but can occur with un-expected changes in order volume.
          • Thank you for your patience as we strive to ship your fire gear as fast as possible.

          Good things take time

          Tracking information is emailed to you once it becomes available. Order status updates are often not available until production is complete. Thank you for your patience!

          Current estimated time until shipping:

          Standard Burners:

          • Made to order
          • 2-3 weeks

          Custom Burners:

          • Made to order
          • 4-5 weeks

          Venture/Arbor Series (Steel/wood):

          • Made to order
          • 5-7 Weeks

          In Stock (Fast Ship) Options:

          • 1-2 Weeks

          Gather Series (Concrete):

          • Made to order
          • 8 Weeks

          Fire Media:

          • 2-4 Weeks
          • Backorder dates will be listed on the product if applicable

          Ready to Finish Kits:

          • Made to order
          • 4-6 Weeks

          Color Samples:

          • 5-7 Days

          Fire Pit Parts

          • 5-7 Days

          Firestorm Portable: 

          • In Stock
          • 5-7 business days

          Transit time not included. Expect 1-2 weeks for the shipment to arrive.

          Shipping Costs

          Please add products to your cart and enter your address at checkout to see detailed shipping costs

          *Free Shipping: Applies to most orders over $99 in the continental U.S. with the following exceptions:

          • Burners over 50″: $279.00

          *Shipping to Canada: You may be charged additional border fees and taxes when you receive your product. Montana Fire Pits is not responsible for those fees.

          *Please add products to your cart and enter your address to see more information on shipping costs to Canada, Hawaii, and Alaska

          []